Cleckheaton 2024: your water explained
Published results for this named supply area. Your address may be served by a different area.
Confirm your address · Check a postcode
Check your full postcode before assuming this area report describes the water serving your address.
Your water at a glance
Soft water. Know your mineral level.
This figure helps you choose appliance settings. Hardness describes dissolved minerals and does not establish whether every water-quality requirement was met.
88 mg/l as CaCO₃
Converted from 35.3875 mg Ca/l (total hardness expressed as calcium) × 2.5 ≈ 88.4688 mg/l as CaCO₃, shown rounded to the nearest whole mg/l.
Soft ≤100 · Slightly hard ≤150 · Moderately hard ≤200 · Hard ≤300 · Very hard >300 mg/l. DWI hardness bands; not safety grades.
Published quality checks
113 parameters: no exceedances reported
These labels describe 2024. 4 other parameters have no complete compliance judgement here. They are not a guarantee about an individual tap today.
Understand the reported results ↓Make this useful for your home
Hardness reporting period: 2024 · Quality reporting period: 2024
Appliance settings · Convert hardness units
0.88 mmol/l
A conversion of the published hardness, not another test. Follow your appliance’s model-specific instructions.
Drinking-water results
What do the important results mean?
Read the status, sample range and source requirement together. A low average can hide an individual exceedance. Green labels mean the supplier reported no exceedances for that parameter and period; amber calls for source context.
E. coli
✓ No exceedances reported
Published mean
0 no'/100 ml
Source reference: 0 no'/100 ml
A microbiological indicator. The reported sample results and any failures matter more than an average bacterial count.
60 samples · Range: 0 to 0 no'/100 ml
The source reports 0 failures across 60 samples. This describes the published period.
Lead
✓ No exceedances reported
Published mean
<0.386 μg/l
Source reference: 10 μg/l
Plumbing can affect lead at an individual tap. An area average cannot rule out a problem with pipes at your property.
8 samples · Range: < 0.02 to 2.66 μg/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Nitrate
✓ No exceedances reported
Published mean
<2.1637 mg NO3/l
Source reference: 50 mg NO3/l
A dissolved compound monitored against drinking-water requirements. Its mean, highest reported result and sample count answer different questions.
8 samples · Range: < 2.13 to 2.4 mg NO3/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Fluoride
✓ No exceedances reported
Published mean
<0.047 mg F/l
Source reference: 1.5 mg F/l
Can occur naturally or be added through a fluoridation scheme. The concentration alone does not tell you whether it was added; a lower number is not automatically better.
12 samples · Range: < 0.04 to 0.06 mg F/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
For your household
What should you do next?
Check appliance settings
Match the hardness unit to your dishwasher manual. Settings depend on the model.
Dishwasher guideUnderstand treatment options
A filter and a softener do different jobs. Start with the household problem you want to solve.
Filters and limescaleA new change at your tap?
For a new taste, smell, colour or supply problem, check current supplier advice. Annual data is not a live incident feed.
Official supplier help ↗Taste, appearance and mineral content
Chlorine, pH and minerals answer different questions. Calcium and magnesium help describe hardness; chloride is different from treatment chlorine. None is a stand-alone water-quality score.
Free chlorine residual
Disinfectant remaining after treatment. It can influence taste and smell; a lower concentration is not automatically better.
See the measurement and context ↓Total chlorine residual
Disinfectant remaining after treatment. It can influence taste and smell; a lower concentration is not automatically better.
See the measurement and context ↓pH
Describes acidity and alkalinity on a scale, rather than an amount of a substance. Where the source gives a range, both its lower and upper bounds matter.
See the measurement and context ↓Calcium
A naturally occurring mineral that contributes to hardness. Calcium alone is not the same measurement as total hardness.
See the measurement and context ↓Has the hardness changed?
History for this reported source area. Only comparable annual statistics appear in the chart; rolling summaries are kept separate. These are not daily tests at your address.
A comparable historical series is not available yet. We will add earlier reports when we can verify their periods and source areas.
Explore all measurements · 120 parameters · 2024
Every result retains its original units, range, sample count and source notes. Comparisons use the reference printed in this report; qualitative references and missing limits are not converted into invented pass/fail judgements. Unlisted substances are not necessarily absent from the water.
Parameters without their own explanation: A substance monitored in this supplier report. The source reference, units, sample range and any reported failures provide its context; the number alone is not a water-quality rating.
Source note on 119 of these parameters: “Source also reports 0 failures (0.00%) against its undertaking standard. Qualified values are taken at face value in the supplier's calculations.”
A failure count (under “Original wording and source notes”) supports a pass/fail label only where the report gives an applicable limit for that parameter.
Hardness and minerals 7 parameters
Chloride
✓ No exceedances reported
Published mean
7.3333 mg Cl/l
Source reference: 250 mg Cl/l
A dissolved salt component that can influence taste at higher concentrations. It is different from chlorine used in treatment.
12 samples · Range: 6.3 to 8.2 mg Cl/l
The source reports 0 failures across 12 samples. This describes the published period.
Original wording and source notes
Source reference: 250. Source parameter: Chloride. Original mean: 7.3333 mg Cl/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Fluoride
✓ No exceedances reported
Published mean
<0.047 mg F/l
Source reference: 1.5 mg F/l
Can occur naturally or be added through a fluoridation scheme. The concentration alone does not tell you whether it was added; a lower number is not automatically better.
12 samples · Range: < 0.04 to 0.06 mg F/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 1.5. Source parameter: Fluoride. Original mean: < 0.047 mg F/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Sodium
✓ No exceedances reported
Published mean
6.3 mg Na/l
Source reference: 200 mg Na/l
A dissolved salt component. Compare the water measurement with its source reference; it is not a measure of your total dietary salt intake.
8 samples · Range: 5.47 to 6.8 mg Na/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 200. Source parameter: Sodium. Original mean: 6.3 mg Na/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Sulphate
✓ No exceedances reported
Published mean
40.8375 mg SO4/l
Source reference: 250 mg SO4/l
A dissolved mineral component monitored in water-quality reports. Read its concentration alongside the source reference.
8 samples · Range: 33.2 to 50 mg SO4/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 250. Source parameter: Sulphate. Original mean: 40.8375 mg SO4/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Calcium
No numerical limit supplied
Published mean
32.5 mg Ca/l
Source reference: -
A naturally occurring mineral that contributes to hardness. Calcium alone is not the same measurement as total hardness.
8 samples · Range: 25.5 to 38.2 mg Ca/l
This report gives no numerical limit for this parameter. A higher or lower number is not automatically better.
Original wording and source notes
Source reference: -. Source parameter: Calcium. Original mean: 32.5 mg Ca/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Magnesium
No numerical limit supplied
Published mean
1.7512 mg Mg/l
Source reference: -
A naturally occurring mineral that contributes to hardness alongside calcium.
8 samples · Range: 1.44 to 2.05 mg Mg/l
This report gives no numerical limit for this parameter. A higher or lower number is not automatically better.
Original wording and source notes
Source reference: -. Source parameter: Magnesium. Original mean: 1.7512 mg Mg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Total hardness
No numerical limit supplied
Converted mean
88.4688 mg/l as CaCO₃
Converted from 35.3875 mg Ca/l (total hardness expressed as calcium) × 2.5.
Source reference: -
Dissolved calcium and magnesium affect limescale and appliance settings. This is a mineral description, not a safety score.
8 samples · Range: 69.75 to 103.75 mg/l as CaCO₃
This report gives no numerical limit for this parameter. A higher or lower number is not automatically better.
Original wording and source notes
Source reference: -. Source parameter: Total Hardness. Converted mean: 88.4688 mg/l as CaCO₃.
Unit conversion of supplier total hardness: original mean 35.3875 mg Ca/l, range 27.9–41.5 mg Ca/l. Yorkshire's own converter multiplies total hardness expressed as calcium by 2.5 for calcium-carbonate equivalent. This is not the separate calcium concentration.
Source failure-count field: 0.
Taste, appearance and treatment 9 parameters
Free chlorine residual
No numerical limit supplied
Published mean
0.27 mg/l
Source reference: -
Disinfectant remaining after treatment. It can influence taste and smell; a lower concentration is not automatically better.
60 samples · Range: 0.04 to 0.58 mg/l
This report gives no numerical limit for this parameter. A higher or lower number is not automatically better.
Original wording and source notes
Source reference: -. Source parameter: Residual Disinfectant - Free. Original mean: 0.27 mg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Total chlorine residual
No numerical limit supplied
Published mean
0.37 mg/l
Source reference: -
Disinfectant remaining after treatment. It can influence taste and smell; a lower concentration is not automatically better.
60 samples · Range: 0.14 to 0.73 mg/l
This report gives no numerical limit for this parameter. A higher or lower number is not automatically better.
Original wording and source notes
Source reference: -. Source parameter: Residual Disinfectant - Total. Original mean: 0.37 mg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Colour
✓ No exceedances reported
Published mean
<3 mg/l Pt/Co scale
Source reference: 20 mg/l Pt/Co scale
A measure of water colour under test conditions. A new change at your tap should be checked with your supplier.
24 samples · Range: < 3 to < 3 mg/l Pt/Co scale
The source reports 0 failures across 24 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 20. Source parameter: Colour. Original mean: < 3 mg/l Pt/Co scale.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Conductivity
✓ No exceedances reported
Published mean
188.38 μS/cm
Source reference: 2500 μS/cm
Indicates how readily water conducts electricity, influenced by dissolved ions. It is not a direct measurement of hardness or safety.
24 samples · Range: 143 to 235 μS/cm
The source reports 0 failures across 24 samples. This describes the published period.
Original wording and source notes
Source reference: 2500. Source parameter: Conductivity. Original mean: 188.38 μS/cm.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
pH
✓ No exceedances reported
Published mean
7.48 pH value
Source reference: 6.5 - 9.5 pH value
Describes acidity and alkalinity on a scale, rather than an amount of a substance. Where the source gives a range, both its lower and upper bounds matter.
24 samples · Range: 7.1 to 7.68 pH value
The source reports 0 failures across 24 samples. This describes the published period.
Original wording and source notes
Source reference: 6.5 - 9.5. Source parameter: Hydrogen Ion (pH). Original mean: 7.48 pH value.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Odour
✓ No exceedances reported
Published mean
0 dilution number
Source reference: 0 dilution number
A sensory assessment of smell in the sampled water. It cannot identify the cause of a current change at your tap.
24 samples · Range: 0 to 0 dilution number
The source reports 0 failures across 24 samples. This describes the published period.
Original wording and source notes
Source reference: 0. Source parameter: Odour. Original mean: 0 dilution number.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Taste
✓ No exceedances reported
Published mean
0 dilution number
Source reference: 0 dilution number
A sensory assessment of the sampled water. It cannot explain a new taste at your home today.
24 samples · Range: 0 to 0 dilution number
The source reports 0 failures across 24 samples. This describes the published period.
Original wording and source notes
Source reference: 0. Source parameter: Taste. Original mean: 0 dilution number.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Total organic carbon
No numerical limit supplied
Published mean
1.817 mg C/l
Source reference: -
A broad measure of organic carbon used to understand water and treatment. It does not identify an individual contaminant.
12 samples · Range: 1.31 to 2.23 mg C/l
This report gives no numerical limit for this parameter. A higher or lower number is not automatically better.
Original wording and source notes
Source reference: -. Source parameter: Total organic carbon. Original mean: 1.817 mg C/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Turbidity
✓ No exceedances reported
Published mean
<0.156 NTU
Source reference: 4 NTU
Measures cloudiness caused by suspended particles. It cannot identify their cause on its own.
24 samples · Range: < 0.07 to 0.36 NTU
The source reports 0 failures across 24 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 4. Source parameter: Turbidity. Original mean: < 0.156 NTU.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Metals 13 parameters
Aluminium
✓ No exceedances reported
Published mean
<13.378 μg Al/l
Source reference: 200 μg Al/l
Monitored as part of water-quality testing and treatment control. Compare with the reference and sample results in the source.
24 samples · Range: < 6.9 to 23.6 μg Al/l
The source reports 0 failures across 24 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 200. Source parameter: Aluminium. Original mean: < 13.378 μg Al/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Antimony
✓ No exceedances reported
Published mean
0.1188 μg Sb/l
Source reference: 5 μg Sb/l
A trace element monitored in drinking water. The source reference and sample results provide the relevant comparison.
8 samples · Range: 0.1 to 0.16 μg Sb/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 5. Source parameter: Antimony. Original mean: 0.1188 μg Sb/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Arsenic
✓ No exceedances reported
Published mean
<0.1512 μg As/l
Source reference: 10 μg As/l
A trace element monitored against a drinking-water requirement. Use the source results and units rather than taste or appearance to interpret it.
8 samples · Range: < 0.12 to 0.18 μg As/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 10. Source parameter: Arsenic. Original mean: < 0.1512 μg As/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Boron
✓ No exceedances reported
Published mean
<0.032 mg B/l
Source reference: 1 mg B/l
A dissolved element monitored in drinking water. The source reference applies to the parameter and units shown here.
12 samples · Range: < 0.032 to 0.0325 mg B/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 1. Source parameter: Boron. Original mean: < 0.032 mg B/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Cadmium
✓ No exceedances reported
Published mean
<0.0288 μg Cd/l
Source reference: 5 μg Cd/l
A trace metal monitored in drinking water. A less-than result reports an upper bound, not a measured zero.
8 samples · Range: < 0.02 to 0.03 μg Cd/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 5. Source parameter: Cadmium. Original mean: < 0.0288 μg Cd/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Chromium
✓ No exceedances reported
Published mean
<0.1712 μg Cr/l
Source reference: 50 μg Cr/l
A trace metal monitored in drinking-water reports. Keep the source’s chemical definition and units when comparing results.
8 samples · Range: < 0.09 to 0.2 μg Cr/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 50. Source parameter: Chromium. Original mean: < 0.1712 μg Cr/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Copper
✓ No exceedances reported
Published mean
0.0115 mg Cu/l
Source reference: 2 mg Cu/l
Can be influenced by plumbing. The area report does not replace investigation of a problem at an individual property.
8 samples · Range: 0.0032 to 0.0303 mg Cu/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 2. Source parameter: Copper. Original mean: 0.0115 mg Cu/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Iron
✓ No exceedances reported
Published mean
<7.49 μg Fe/l
Source reference: 200 μg Fe/l
Can affect water colour, staining and taste. A historical result does not diagnose a change in your tap water today.
24 samples · Range: < 3.72 to 48.4 μg Fe/l
The source reports 0 failures across 24 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 200. Source parameter: Iron. Original mean: < 7.49 μg Fe/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Lead
✓ No exceedances reported
Published mean
<0.386 μg/l
Source reference: 10 μg/l
Plumbing can affect lead at an individual tap. An area average cannot rule out a problem with pipes at your property.
8 samples · Range: < 0.02 to 2.66 μg/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 10. Source parameter: Lead. Original mean: < 0.386 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Manganese
✓ No exceedances reported
Published mean
<0.57 μg Mn/l
Source reference: 50 μg Mn/l
Can affect colour and deposits. Any reported exceedance needs the supplier’s investigation context.
24 samples · Range: < 0.3 to 1.12 μg Mn/l
The source reports 0 failures across 24 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 50. Source parameter: Manganese. Original mean: < 0.57 μg Mn/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Mercury
✓ No exceedances reported
Published mean
<0.045 μg Hg/l
Source reference: 1 μg Hg/l
A trace metal monitored against drinking-water requirements. Keep detection limits separate from exact measurements.
12 samples · Range: < 0.04 to < 0.06 μg Hg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 1. Source parameter: Mercury. Original mean: < 0.045 μg Hg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Nickel
✓ No exceedances reported
Published mean
0.938 μg Ni/l
Source reference: 20 μg Ni/l
A monitored metal that can be influenced by materials in contact with water. Local plumbing and sampling context matter.
8 samples · Range: 0.59 to 1.68 μg Ni/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 20. Source parameter: Nickel. Original mean: 0.938 μg Ni/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Selenium
✓ No exceedances reported
Published mean
<0.26 μg Se/l
Source reference: 10 μg Se/l
A trace element monitored in drinking water. Its presence alone does not establish that a requirement was exceeded.
8 samples · Range: < 0.08 to < 0.32 μg Se/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 10. Source parameter: Selenium. Original mean: < 0.26 μg Se/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Microbiology 4 parameters
Colony count at 22°C
No numerical limit supplied
Published mean
0 no'/ml
Source reference: -
A general bacterial count used to monitor changes in the supply. It is not equivalent to an E. coli result.
24 samples · Range: 0 to 1 no'/ml
This report gives no numerical limit for this parameter. A higher or lower number is not automatically better.
Original wording and source notes
Source reference: -. Source parameter: Colony Counts After 3 Days At 22øc. Original mean: 0 no'/ml.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
E. coli
✓ No exceedances reported
Published mean
0 no'/100 ml
Source reference: 0 no'/100 ml
A microbiological indicator. The reported sample results and any failures matter more than an average bacterial count.
60 samples · Range: 0 to 0 no'/100 ml
The source reports 0 failures across 60 samples. This describes the published period.
Original wording and source notes
Source reference: 0. Source parameter: E. coli. Original mean: 0 no'/100 ml.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Enterococci
✓ No exceedances reported
Published mean
0 no'/100 ml
Source reference: 0 no'/100 ml
A microbiological indicator assessed through sample results. Read any reported failures with the supplier’s investigation notes.
8 samples · Range: 0 to 0 no'/100 ml
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 0. Source parameter: Enterococci. Original mean: 0 no'/100 ml.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Coliform bacteria
✓ No exceedances reported
Published mean
0 no'/100 ml
Source reference: 0 no'/100 ml
Used to monitor water-system hygiene. Interpret detections with the supplier’s sampling location and investigation notes.
60 samples · Range: 0 to 0 no'/100 ml
The source reports 0 failures across 60 samples. This describes the published period.
Original wording and source notes
Source reference: 0. Source parameter: Total coliforms(Indicator). Original mean: 0 no'/100 ml.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Other monitored substances 87 parameters
1,2 Dichloroethane
✓ No exceedances reported
Published mean
<0.2 μg/l
Source reference: 3 μg/l
About this parameter: see the note above this list.
8 samples · Range: < 0.16 to < 0.16 μg/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 3. Source parameter: 1,2 Dichloroethane. Original mean: < 0.2 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Ammonium(ammonia and ammonium ions)
✓ No exceedances reported
Published mean
<0.0117 mg NH4/l
Source reference: 0.5 mg NH4/l
About this parameter: see the note above this list.
24 samples · Range: < 0.008 to 0.064 mg NH4/l
The source reports 0 failures across 24 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.5. Source parameter: Ammonium(ammonia and ammonium ions). Original mean: < 0.0117 mg NH4/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Benzene
✓ No exceedances reported
Published mean
<0.06 μg/l
Source reference: 1 μg/l
About this parameter: see the note above this list.
8 samples · Range: < 0.06 to < 0.06 μg/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 1. Source parameter: Benzene. Original mean: < 0.06 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Benzo 3,4 pyrene
✓ No exceedances reported
Published mean
<0.0004 ug/l
Source reference: 0.01 ug/l
About this parameter: see the note above this list.
8 samples · Range: < 0.00042 to < 0.00042 ug/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.01. Source parameter: Benzo 3,4 pyrene. Original mean: < 0.0004 ug/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Bromate
✓ No exceedances reported
Published mean
0.4875 μg BrO3/l
Source reference: 10 μg BrO3/l
About this parameter: see the note above this list.
8 samples · Range: 0.3 to 0.7 μg BrO3/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 10. Source parameter: Bromate. Original mean: 0.4875 μg BrO3/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Cyanide
✓ No exceedances reported
Published mean
<1.2 μg CN/l
Source reference: 50 μg CN/l
About this parameter: see the note above this list.
12 samples · Range: < 1.2 to < 1.2 μg CN/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 50. Source parameter: Cyanide. Original mean: < 1.2 μg CN/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Nitrate
✓ No exceedances reported
Published mean
<2.1637 mg NO3/l
Source reference: 50 mg NO3/l
A dissolved compound monitored against drinking-water requirements. Its mean, highest reported result and sample count answer different questions.
8 samples · Range: < 2.13 to 2.4 mg NO3/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 50. Source parameter: Nitrate. Original mean: < 2.1637 mg NO3/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Nitrite - Consumer's Taps
✓ No exceedances reported
Published mean
<0.0021 mg/l NO2
Source reference: 0.5 mg/l NO2
About this parameter: see the note above this list.
8 samples · Range: < 0.002 to < 0.003 mg/l NO2
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.5. Source parameter: Nitrite - Consumer's Taps. Original mean: < 0.0021 mg/l NO2.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Nitrite/ Nitrate formula
✓ No exceedances reported
Published mean
0.0062 mg/l
Source reference: 1 mg/l
About this parameter: see the note above this list.
8 samples · Range: 0 to 0.05 mg/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 1. Source parameter: Nitrite/ Nitrate formula. Original mean: 0.0062 mg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Polycyclic Aromatic Hydrocarbons (PAHs)
✓ No exceedances reported
Published mean
0 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
8 samples · Range: 0 to 0 μg/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 0.1. Source parameter: Polycyclic Aromatic Hydrocarbons (PAHs). Original mean: 0 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Tetrachloroethene/Trichlorethene - Sum
✓ No exceedances reported
Published mean
0 μg/l
Source reference: 10 μg/l
About this parameter: see the note above this list.
8 samples · Range: 0 to 0 μg/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 10. Source parameter: Tetrachloroethene/Trichlorethene - Sum. Original mean: 0 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Tetrachloromethane
✓ No exceedances reported
Published mean
<0.16 μg/l
Source reference: 3 μg/l
About this parameter: see the note above this list.
8 samples · Range: < 0.16 to < 0.16 μg/l
The source reports 0 failures across 8 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 3. Source parameter: Tetrachloromethane. Original mean: < 0.16 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Total Trihalomethanes (THM's)
✓ No exceedances reported
Published mean
48.4287 μg/l
Source reference: 100 μg/l
About this parameter: see the note above this list.
8 samples · Range: 27.62 to 63.05 μg/l
The source reports 0 failures across 8 samples. This describes the published period.
Original wording and source notes
Source reference: 100. Source parameter: Total Trihalomethanes (THM's). Original mean: 48.4287 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
2,4,5-T
✓ No exceedances reported
Published mean
<0.0137 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.013 to < 0.015 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: 2,4,5-T. Original mean: < 0.0137 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
2,4-D
✓ No exceedances reported
Published mean
<0.0109 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.01 to 0.017 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: 2,4-D. Original mean: < 0.0109 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
2,4-DB
✓ No exceedances reported
Published mean
<0.0113 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.01 to < 0.012 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: 2,4-DB. Original mean: < 0.0113 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Aldrin
✓ No exceedances reported
Published mean
<0.008 μg/l
Source reference: 0.03 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.008 to < 0.008 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.03. Source parameter: Aldrin. Original mean: < 0.008 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Atrazine
✓ No exceedances reported
Published mean
<0.006 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Atrazine. Original mean: < 0.006 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Azoxystrobin
✓ No exceedances reported
Published mean
<0.006 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Azoxystrobin. Original mean: < 0.006 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Bentazone
✓ No exceedances reported
Published mean
<0.0043 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.004 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Bentazone. Original mean: < 0.0043 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Bixafen
✓ No exceedances reported
Published mean
<0.012 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.012 to < 0.012 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Bixafen. Original mean: < 0.012 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Boscalid
✓ No exceedances reported
Published mean
<0.008 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.008 to < 0.008 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Boscalid. Original mean: < 0.008 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Bromacil
✓ No exceedances reported
Published mean
<0.011 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.011 to < 0.011 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Bromacil. Original mean: < 0.011 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Bromoxynil
✓ No exceedances reported
Published mean
<0.008 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.007 to < 0.01 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Bromoxynil. Original mean: < 0.008 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Carbetamide
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Carbetamide. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Chlormequat
✓ No exceedances reported
Published mean
<0.0075 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.002 to < 0.008 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Chlormequat. Original mean: < 0.0075 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Chlorpropham
✓ No exceedances reported
Published mean
<0.0077 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Chlorpropham. Original mean: < 0.0077 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Chlorpyrifos
✓ No exceedances reported
Published mean
<0.008 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.008 to < 0.008 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Chlorpyrifos. Original mean: < 0.008 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Chlortoluron
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Chlortoluron. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Clomazone
✓ No exceedances reported
Published mean
<0.007 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.007 to < 0.007 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Clomazone. Original mean: < 0.007 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Clopyralid
✓ No exceedances reported
Published mean
<0.0117 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.011 to < 0.012 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Clopyralid. Original mean: < 0.0117 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Cyanazine
✓ No exceedances reported
Published mean
<0.007 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.007 to < 0.007 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Cyanazine. Original mean: < 0.007 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Cypermethrin
✓ No exceedances reported
Published mean
<0.008 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.008 to < 0.008 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Cypermethrin. Original mean: < 0.008 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Cyproconazole
✓ No exceedances reported
Published mean
<0.006 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Cyproconazole. Original mean: < 0.006 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Diazinon
✓ No exceedances reported
Published mean
<0.007 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.007 to < 0.007 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Diazinon. Original mean: < 0.007 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Dicamba
✓ No exceedances reported
Published mean
<0.0113 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.011 to < 0.012 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Dicamba. Original mean: < 0.0113 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Dichlobenil
✓ No exceedances reported
Published mean
<0.004 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.004 to < 0.004 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Dichlobenil. Original mean: < 0.004 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Dichlorprop
✓ No exceedances reported
Published mean
<0.0073 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.01 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Dichlorprop. Original mean: < 0.0073 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Dieldrin
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.03 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.03. Source parameter: Dieldrin. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Difenconazole
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Difenconazole. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Diflufenican
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Diflufenican. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Diuron
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Diuron. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Epoxiconazole
✓ No exceedances reported
Published mean
<0.006 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Epoxiconazole. Original mean: < 0.006 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
EPTC
✓ No exceedances reported
Published mean
<0.022 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.022 to < 0.022 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: EPTC. Original mean: < 0.022 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Flufenacet
✓ No exceedances reported
Published mean
<0.008 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.008 to < 0.008 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Flufenacet. Original mean: < 0.008 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Fluroxypyr
✓ No exceedances reported
Published mean
<0.01 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.008 to < 0.011 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Fluroxypyr. Original mean: < 0.01 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Flurtamone
✓ No exceedances reported
Published mean
<0.007 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.007 to < 0.007 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Flurtamone. Original mean: < 0.007 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Flusilazole
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Flusilazole. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Flutriafol
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Flutriafol. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Fluxapyroxad
✓ No exceedances reported
Published mean
<0.01 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.01 to < 0.01 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Fluxapyroxad. Original mean: < 0.01 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Gamma-HCH (Lindane)
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Gamma-HCH (Lindane). Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Heptachlor
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.03 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.03. Source parameter: Heptachlor. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Heptachlor epoxide
✓ No exceedances reported
Published mean
<0.007 μg/l
Source reference: 0.03 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.007 to < 0.007 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.03. Source parameter: Heptachlor epoxide. Original mean: < 0.007 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Imazapyr
✓ No exceedances reported
Published mean
<0.0053 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.004 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Imazapyr. Original mean: < 0.0053 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Ioxynil
✓ No exceedances reported
Published mean
<0.0043 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.004 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Ioxynil. Original mean: < 0.0043 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Isoproturon
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Isoproturon. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Linuron
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Linuron. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
MCPA
✓ No exceedances reported
Published mean
<0.0094 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to 0.03 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: MCPA. Original mean: < 0.0094 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Mecoprop-P
✓ No exceedances reported
Published mean
<0.0097 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.01 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Mecoprop-P. Original mean: < 0.0097 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Mepiquat chloride
✓ No exceedances reported
Published mean
<0.0076 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.003 to < 0.008 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Mepiquat chloride. Original mean: < 0.0076 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Metaldehyde
✓ No exceedances reported
Published mean
<0.006 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Metaldehyde. Original mean: < 0.006 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Metamitron
✓ No exceedances reported
Published mean
<0.008 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.008 to < 0.008 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Metamitron. Original mean: < 0.008 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Metazachlor
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Metazachlor. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Metobromuron
✓ No exceedances reported
Published mean
<0.01 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.01 to < 0.01 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Metobromuron. Original mean: < 0.01 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Monuron
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Monuron. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
op'-DDD (TDE)
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: op'-DDD (TDE). Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
op'-DDE
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: op'-DDE. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
op'-DDT
✓ No exceedances reported
Published mean
<0.004 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.004 to < 0.004 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: op'-DDT. Original mean: < 0.004 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Oxadixyl
✓ No exceedances reported
Published mean
<0.012 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.012 to < 0.012 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Oxadixyl. Original mean: < 0.012 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Pendimethalin
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Pendimethalin. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Pesticides - Total Substances
✓ No exceedances reported
Published mean
0.0064 μg/l
Source reference: 0.5 μg/l
About this parameter: see the note above this list.
12 samples · Range: 0 to 0.066 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
Original wording and source notes
Source reference: 0.5. Source parameter: Pesticides - Total Substances. Original mean: 0.0064 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
pp'-DDD (TDE)
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: pp'-DDD (TDE). Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
pp'-DDE
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: pp'-DDE. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
pp'-DDT
✓ No exceedances reported
Published mean
<0.004 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.004 to < 0.004 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: pp'-DDT. Original mean: < 0.004 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Propachlor
✓ No exceedances reported
Published mean
<0.007 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.007 to < 0.007 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Propachlor. Original mean: < 0.007 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Propamocarb
✓ No exceedances reported
Published mean
<0.0047 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.004 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Propamocarb. Original mean: < 0.0047 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Propham
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Propham. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Propiconazole
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Propiconazole. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Propyzamide
✓ No exceedances reported
Published mean
<0.009 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.009 to < 0.009 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Propyzamide. Original mean: < 0.009 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Prosulfocarb
✓ No exceedances reported
Published mean
<0.006 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Prosulfocarb. Original mean: < 0.006 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Prothioconazole-desthio
✓ No exceedances reported
Published mean
<0.007 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.007 to < 0.007 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Prothioconazole-desthio. Original mean: < 0.007 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Quinmerac
✓ No exceedances reported
Published mean
<0.006 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Quinmerac. Original mean: < 0.006 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Simazine
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Simazine. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Tebuconazole
✓ No exceedances reported
Published mean
<0.006 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Tebuconazole. Original mean: < 0.006 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Tri-allate
✓ No exceedances reported
Published mean
<0.006 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.006 to < 0.006 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Tri-allate. Original mean: < 0.006 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Trichlopyr
✓ No exceedances reported
Published mean
<0.018 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.016 to 0.019 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Trichlopyr. Original mean: < 0.018 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Trietazine
✓ No exceedances reported
Published mean
<0.005 μg/l
Source reference: 0.1 μg/l
About this parameter: see the note above this list.
12 samples · Range: < 0.005 to < 0.005 μg/l
The source reports 0 failures across 12 samples. This describes the published period.
“<” is part of the source result. It is not an exact concentration or a measured zero.
Original wording and source notes
Source reference: 0.1. Source parameter: Trietazine. Original mean: < 0.005 μg/l.
Source note: printed once above this list (the same note appears on 119 parameters).
Source failure-count field: 0.
Sources, dates and how to interpret this page
- Reporting period
- 2024
- Source retrieved
- 2026-09-11
- Last verified source check
- 2026-09-11
- Original publication
- Yorkshire Water report ↗
Official supplier report for this supply zone, retrieved with postcode BD19 3JQ. Town pages that cite this zone show their own supplier-confirmed example postcode. This is an example supply area, not a measurement at every address in the towns it serves.
Annual report period is read from the PDF, separately from any year in the zone name. Total hardness is converted using Yorkshire’s factor of 2.5 from mg Ca/l to mg/l as CaCO₃.
All published numeric parameters are retained, including censored readings and historical failures. These results are not a statement about current incidents.
Unit conversion of supplier total hardness: original mean 35.3875 mg Ca/l, range 27.9–41.5 mg Ca/l. Yorkshire's own converter multiplies total hardness expressed as calcium by 2.5 for calcium-carbonate equivalent. This is not the separate calcium concentration.
Hardness: 8 samples · reported range 69.75 to 103.75 mg/l as CaCO₃.
Yorkshire total hardness expressed as calcium is converted to calcium carbonate using the supplier’s factor of 2.5. The separate calcium measurement is not total hardness.
Status labels describe the published parameter and period. Historical exceedances do not automatically establish a current incident. Numerical limits are taken from the original report, not applied indiscriminately across countries, dates or sampling locations. DWI explains how standards work in England and Wales.
Keep this report
Link to Cleckheaton 2024Saved areas stay on this device. This does not subscribe you to messages or emergency alerts.
Help us make this clearer
Optional, anonymous feedback. Please answer based on what the report explained.
What does this report describe?
Did this help answer your question?
We store daily answer counts, without names or visitor identifiers. Repeated answers can contribute; this is not a representative survey.
Town pages for this source area
These town pages show this area's approved report. A town can span several supply areas; check your postcode for your address.